Step III: Convert Individual PDF Files to TIFFsIn Photoshop:1.File→Open the PDF. You will need to do this one page at a time. Make sure you're importing it at 300ppi, RGB.2.Use the Crop Tool (fifth from the top of the toolbar) to select an area clo

来源:学生作业帮助网 编辑:作业帮 时间:2024/05/10 20:21:10
Step III: Convert Individual PDF Files to TIFFsIn Photoshop:1.File→Open the PDF. You will need to do this one page at a time. Make sure you're importing it at 300ppi, RGB.2.Use the Crop Tool (fifth from the top of the toolbar) to select an area clo

Step III: Convert Individual PDF Files to TIFFsIn Photoshop:1.File→Open the PDF. You will need to do this one page at a time. Make sure you're importing it at 300ppi, RGB.2.Use the Crop Tool (fifth from the top of the toolbar) to select an area clo
Step III: Convert Individual PDF Files to TIFFs
In Photoshop:
1.File→Open the PDF. You will need to do this one page at a time. Make sure you're importing it at 300ppi, RGB.
2.Use the Crop Tool (fifth from the top of the toolbar) to select an area close to the borders of your image. Hit Enter to apply the crop.
3.Layer→Flatten Image
4.Image→Image Size. Uncheck the Resample Image checkbox. If the Width is over 17.35cm, type 17.35 in the Width box (17.35cm is our maximum allowable width for figures). The Resolution will go up automatically as the Width decreases. If the resolution does not hit 300 when you make the Width 17.35, type 300 in Resolution and as long as Width doesn't go below 8.3cm, everything is fine. Also, the height cannot be more than 23.35. If the Height and Width are within these prescribed limits, no adjustment to your figure size needs to be made.
5.File→Save As. Save as TIFF, Image Compression set to LZW, Pixel Order set to Interleaved, Byte Order set to IBM PC.
请问第四步怎么操作,?没看到哪里有长宽值会不断的变呀

Step III: Convert Individual PDF Files to TIFFsIn Photoshop:1.File→Open the PDF. You will need to do this one page at a time. Make sure you're importing it at 300ppi, RGB.2.Use the Crop Tool (fifth from the top of the toolbar) to select an area clo

晕, 提问的高人, 您不会用中文版啊 ... 

4. 就是图片的大小啊, 

中文对应的就是  图象 - 图象大小

缩放比列了 , 系统默认的选择"约束比列", 当然 宽度数值修改, 高度的数值也修改啊 .

你不选这个 就不跟着修改了,

最下面最下面的Resample Image  , 这个就是 重定图象像素~ 不用选

我也不用中文版的, 鬼知道对应的是什么啊~  

您应该认识英文单词吧 . 

您这个是考大家 英文水平还是考技术操作啊 . 

头顶雷声轰轰 

补充的 -----------------------------------------------------------------------

我也不太正常,竟然还给您找了 

Image - Image Size, 弹出个对话框, 看图片, 

constrain proportions 前面的选择要选 .自动更改比列的... 大哥您认识英文不啊 ... 

宽不超过 在8.3到17.35cm之间, 高不超过 23.35, 像素 300

自己对应吧 

这老兄是来找翻译的~ 

以后这样问题 别来技术区问, 问翻译~